Please feel free to call us.

+49 (0)212 380 310

Monday till Friday
09:00 bis 17:00 Uhr

Model si

Dry cleaning of coarse and fine dirt (small stones, grit, metal chips, sand, leaves, fine metal chips, rubber abrasion, dust)
Categories
Tub material
Stainless steel V2A 1.4301
Brush strip material
Body: PVC; Fibres: PA 6.0
Escape route suitability
Usability verified by WAZ
Location
Interior passage
Grating material
Stainless steel V2A 1.4301
Fire protection
tested in accordance with DIN 13501-1 Bfl-s1
Cleaning effect
verified by Frauenhofer IPA
Image
UP TO 80 % LESS DIRT

Reduces the carry-over of dirt at the transitions between production and logistics halls

Image
FULL STAINLESS STEEL

With the corrosion-resistant stainless steel grates, our Aqua models can be operated permanently wet and with disinfectant chemistry.

Image
Medium mesh grate size

This series has a medium-mesh grating size so that the rollers of pallet trucks and tugger trains run smoothly and without resistance over our clean-off zones.

 

_ Dirt collection tray in two heights   
 

To prevent dirt from being dispersed within production and logistics halls, it is collected in a collection tray under the cleaning mats.

The choice of the right tray size depends on three decisive factors:

  1. requirements
    Before making a decision, it must be clear what the situation is like on site, whether cleaning is to take place inside, outside or in both places and how wide the passageways are.
  2. vehicles and frequency
    Which vehicles cross the clean-off zone? Do shoe treads also need to be cleaned? How many crossings take place per day? If the frequency is higher, we recommend using a deeper tray because more dirt can be collected. 
  3. maintenance intervals
    The deeper the tray, the more dirt it can hold and the longer the cleaning interval. This saves you work, as the collection trays need to be cleaned less frequently. 
     
Image
ProfilGate® si55
  • 10 mm dirt collection reservoir 
  • For <100 passes per day


     

Wannensystem transparent_750_T.png

 
 
_ Modular System

The ProfilGate® clean-off zone modules are available in two standard widths that can be individually combined (see drawing). This enables us to optimally adapt them to the requirements of your production and logistics halls.

You give us the dimensions of the entrances and transitions where you would like to use our clean-off zones and we will put together the right modules for you.

Of course, we will also be happy to advise you personally on site and take the measurements ourselves.

_ Determining the correct cleaning field length

Based on the analysis by the Fraunhofer IPA Institute and IBELIN laboratory, we know exactly the length at which our clean driving zones achieve their optimum cleaning effect. To get a rough estimate of this, you can use the following rules of thumb for planning:

Transport vehicles: At least three tire rotations are enough to remove 80 % of the dirt. This means that your cleaning area should be at least 3 - 4 times the tread area of the largest tire circumference to be cleaned.

Shoe soles: For cleaning shoe soles, each foot should have at least four to six contacts with the cleaning field with a normal stride length.

Of course, the conditions on site play a decisive role in exact planning. These include the type of vehicle and dirt, dry or wet cleaning and much more. If you have any questions on this topic, we will be happy to advise you. 

Transparent_Rollenabwicklung.png

Image
YOUR PERSONAL CONTACT
"Contact us for all your industrial cleaning needs. We will help you choose the right products for your clean factory".

Malte Ottmann, Head of Int. Sales

Address

HEUTE Maschinenfabrik GmbH & Co. KG

Höhscheider Weg 37
42699 Solingen

Opening hours

Monday till Friday
09:00 bis 17:00 Uhr

+49 (0)212 380 310
Message